Native Instruments Traktor Kontrol X1 MK2 Guide d'installation

Manual

2.2 Rear Panel The Rear panel of the X12.3 TRAKTOR KONTROL X1 Modes When using the TRAKTOR KONTROL X1 with TRAKTOR, the default configuration o

The SHIFT, Load Left, and Load Right area used for MIDI mode►To leave MIDI mode and return to native TRAKTOR control, hold SHIFT and press both(backli

3 Key functions when using the X1 with TRAKTOR This chapter details the use of the X1 with TRAKTOR, whilst offering detailed explanations ofthe device

If you wish to change this, you can do so at the point of opening TRAKTOR, or at any pointby disconnecting, and subsequently reconnecting the device&a

1. To scroll through your Track Collection in TRAKTOR, turn the BROWSE encoder eitherleft, or right.2. To navigate your way to another col

3.4 Deck Control 3.4.1 Using the Touch Strip in Split Mode The X1's Touch Strip can be used to control two TRAKTOR Decks together,

The Touch Strip in Split Mode.Using the X1's default Deck combination A & B:(1) This area controls Deck A(2) This area controls Deck BTry out

This technique can be used to select a suitable start point, or for more advanced techni-ques like scratching, or spinbacks.3.4.2 Primary Functio

Using the SHIFT button to perform a Touch Strip needle drop.Practice using the Touch Strip in its default Split Mode. Getting used to using the vis

3.4.4 Resizing the Touch Strip (Single Mode) The X1 allows you to use the Touch Strip to control an individual TRAKTOR Deck (known asSingle Mode),

The information in this document is subject to change without notice and does not represent acommitment on the part of Native Instruments GmbH.

2. Slide your finger either fully to the right, as shown below, to expand the left deck, or fullyto the left to expand the right deck.Switching TRAKTO

1. Hold your finger on the Touch Strip, beneath where you see the orange dot. The LED stripabove the Touch Strip will now solely indicate the orange d

▪ Cueing▪ HotCues▪ Deck sync (& Master) functions▪ Flux mode (& Tap mode)This section will take you through the functions of each button

▪ White: Grid MarkerTRAKTOR will save the Beat Grid location as a HotCue point; this is why many tracks willappear with one white button.Setting HotCu

To trigger a Remix Deck cell:►Press one of the HotCue buttons→The corresponding Remix Deck cell will to start playing.To mute playback of a Remix Deck

3.5.2 PLAY buttons Pressing either of the PLAY buttons will toggle playback on the corresponding TRAKTOR deck.Whilst the track is playing, pressing th

3.5.5 FLUX Buttons Pressing the FLUX button will engage TRAKTOR's Flux Mode. Flux mode lets you jump to cuepoints and loops without losing the ov

Assigning a Loop to the Touch StripYou can use the Touch Strip to control loops on a TRAKTOR Deck.1. Hold your finger on the Touch Strip assign

4. Whilst this loop mode is still assigned to the Touch Strip, you can engage a loop again atany point by either tapping or holding the Touch Strip.Un

The X1's FX Section3.7.1 Assigning an Effect There is an identical FX section located on either side of the X1, a simple way to think of this,is

GermanyNative Instruments GmbHSchlesische Str. 29-30D-10997 BerlinGermanywww.native-instruments.de USANative Instruments North America, Inc.6725 Sunse

→The FX Assign button will now be backlit orange.►By default, the X1 provides a choice of assigning two TRAKTOR effect units at any onetime. The desig

2. Select Single Mode from the menu in TRAKTOR's effect units 1 and 2, and a differenteffect for each.3. Press the left-hand FX Assign

►Pressing any of FX buttons (backlit orange when engaged)1-3 will engage the correspond-ing individual effect from that Group. The adjacent FX Knob co

1. Hold your finger in the Touch Strip assign area (if a Deck is in Split Mode, two orangedots will be located above center the Touch

The FX (Dry/Wet) knobs located at the top of the X1, control the overall amount of the cor-responding TRAKTOR effect unit. Whilst using the Touch Stri

4 Hardware Reference This section will provide you with a concise overview of each and every hardware componentyou will find on the X1. This has

4.1 Top Panel Top PanelHardware ReferenceTop Panel Traktor Kontrol X1 Mk2 - Manual - 36

4.2 Rear Panel Rear PanelUSB InputUSB InputThe X1 must be connected to your computer via the included USB cable.Kensington LockThe Kensington Lock Por

4.3 Transport Section CUEThe CUE ButtonIf a Deck is stopped, pressing CUE will place the white Cue Marker at the current location—ifthe white Cue Mar

SYNC (MASTER)The SYNC ButtonThe X1's SYNC buttons allow you to manually engage (or disengage) TRAKTOR's sync mode onTRAKTOR's deck.The

Table of Contents1 Welcome to the TRAKTOR KONTROL X1! ...6 1.1 A word about this Do

4.4 FX Section FX Assign buttonsThe FX Assign ButtonsFour of these buttons exist in the transport section of the X1. Two of these are located on eachs

There are three FX buttons (numbered 1-3) on each side of the X1. When a TRAKTOR effectunit is set to Group mode these buttons will in the majority of

4.5 BROWSE, SHIFT and Load Load, SHIFT and BROWSE ButtonsThese two Load buttons (backlit blue) are used to load a track into a TRAKTOR deck. Pressingt

The BROWSE encoder button is integral to using the X1 to navigate your way around your trackcollection, and playlists in TRAKTOR. By default yo

The Touch Strip of the TRAKTOR KONTROL X1 provides an additional form of hands-on con-trol. For more information on how to use the Tourchstrip, please

5 Appendix 5.1 TRAKTOR KONTROL X1 Preferences The below section details the X1's TRAKTOR preferences.Note here that your X1 device will show in T

The X1 Mk2's TRAKTOR preferences5.1.1Browse Encoder By default, when you touch the BROWSE encoder it switches to TRAKTOR's full Browser. Un-

5.1.2 Touch Strip By default the X1's Seek behavior is set to Seek on Stop, which means that, by touching theTouch Strip, you are able to seek th

5.1.3 FLUX Button By default, the X1's FLUX buttons' Primary function is set to Flux Mode in TRAKTOR, (pleaserefer to section ↑3.5.5, FL

Dim State Percentage: When a button is not engaged in its on state, it is still backlit (in itsDim State). This option allows you to either

3.6 Using the Loop Encoders ... 26 3.7 Effec

2. In Default Setups, select both the 1st X1 and 2nd X1 mapping options as C+D.→By default, the TRAKTOR KONTROL X1 Mk2 will control TRAKTOR decks A +

IndexBBROWSE encoder [13]DDeck Combinations [13]Deck Setup [13]EEffects [28]FX (Mode) [40]FX Assign [40]FX Knobs [40]Touch Strip assign [29] [32]TRAKT

TTop Panel [36]Touch Strip [15]Prmary Functions [17]Resize [19] [20]Scratch Control [21]Secondary Functions [17]TRAKTOR preferencesX1 Mk1 [49]X1 Mk2 [

1 Welcome to the TRAKTOR KONTROL X1! Dear Native Instruments customer,Thank you for purchasing the TRAKTOR KONTROL X1, and for your continued trust in

1.2 Document Conventions This document uses particular formatting to point out special facts and to warn you of poten-tial issues. The icons introduci

2 TRAKTOR KONTROL X1 HARDWARE This section will provide you with an overview of the key hardware components on the X1.2.1 Top Panel The image below s

(2) FX (Dry/Wet) Knob(3) FX1 Button(4) FX1 Knob(5) FX2 Button(6) FX2 Knob(7) FX3 Button(8) FX3 Knob(9) FX Assign Buttons(10) Browse Encoder(11) Loop E